Speed Reducer Motor
General specification:
Motor type | Speed Reducer Motor | ||
Frame size | 60 mm / 70mm / 80mm ... | ||
Running speed | Motor 1200-3000 rpm, Gear Ratio 1/3 ~ 1/1800 | ||
Output power | 6W / 10W / 15W / 25W / 40W / 60W / 90W / 120 W /140W / 2000W / 370W ......3700W | ||
Output shaft | 8mm ~ 50mm; roundshaft, D-cut shaft, key-way shaft, | ||
Voltage type | Single Phase 110V/220V; 50Hz/60Hz | ||
Accessories | Brake / Connector / Terminal box / Capacitor / Controller… | ||
Product Photo
ac gear motor
electric motor gear reducer
boiler gear motor
Why do you choose our speed reducer motor?
| Hollow design, built-in fan radiator
● Reduce the motor temperature ● Ensure the high efficiency of the motor ● Prolong the service life of the motor |
High Viscosity Gear Grease ● Excellent adhesion, ● Not easy peeled off or extruded out, the gear surface with excellent lubricity. ● Mechanical stablity and colloidal stablity, long service life. |
|
| High temperature resistant copper coil
● 100% pure copper coil high temperature enameled coil. ● Insulation class F, ensure that the motor is stable, durable, efficient and safe.
|
Terminal box
● High protection level ≥IP55 ● Terminal block against damage from pulling lead wire ● Inside capacitor makes it easier for wire connection ● Iron plate helps avoid damage from mounting screw
|
|
Our motors pass multiple tests:
1. Gear detector for comprehensive tests of gears.
2. Vickers and Rockwell hardness tester to retest the hardness and insure the abrasive resistance.
3. Radial runout tester to test the running-in and balance of the motors, to reduce the abrasion and make sure low noise when high speed running.
4. Withstand voltage tester to test electric leakage or above normal voltage.
5. Interturn tester and surge test to test the insulation between turns in motor stator winding. Bold coil makes bigger torque under the same power torque output.
6. Stator comprehensive tester to test the defect after inserted winding, pick out the defectives.
How to select the right Speed Reducer Motor?
1. Know your application requirements for your gearmotor. The first step in selecting a gearmotor is reviewing your application requirements. These include but are not limited to the following:
General requirements: Envelope size, mounting orientation, mounting type and size, overhung and side loads, and lubrication type.
Input power source: Voltage, frequency (Hz), maximum current (Amps) and control type, if applicable.
Gearmotor specifications: Size, weight, desired noise level, life expectancy and maintenance level.
Gearmotor performance: speed, torque, duty cycle, horsepower, starting and running torque (full load).
Operation environment: Application and ambient temperature, and ingress protection (IP) rating.
2. Select the proper motor.
Next, use your list of application requirements and compare them to the motor specifications of the different types you are interested in such as a universal, brushless DC, AC induction or a permanent magnet gearmotor. Because each application has its own unique characteristics and requirements, it is important to note which factor such as horsepower, starting torque or efficiency is most important to your application. During this phase, you may decide that matching a gearbox and motor separately will best suit your needs.
3. Know the speed and torque requirements of the load to be driven. To ensure your gearmotor is properly sized for your intended application, it’s important to know your output speed, starting and running torque. Selecting the proper gearmotor is a matter of matching output speed (RPM) and torque to your application’s needs. The output speed is determined by your machine’s requirements and should be already known. That leaves the starting and running torque to be determined. Keep in mind, when you choose a pre-engineered gearmotor, the manufacturer has done most of the heavy lifting to ensure the motor and gearbox will work seamlessly.
Once you have calculated your starting and running torque, use a manufacturer’s performance curve for torque, speed and efficiency to find a motor that matches your needs. Then review potential design limitations including the running (full-load) gearbox torque,input speed, gearbox yield strength, thermal characteristics and duty cycles.
4.Test the motor.
FAQ
Q: Can you make the gear motor with customization?
A: Yes, we can customize per your request, like power, voltage, speed, shaft size, flange, terminal box, IP grade, etc.
Q: Do you provide samples?
A: Yes. The sample is available for testing.
Q: What is your MOQ?
A: It is 1pcs for the beginning of our business.
Q: What's your lead time?
A: Standard products need 5-30days, a bit longer for customized products.
Q: Do you provide technical support?
A: Yes. Our company have design and development team, we can provide technical support if you
need.
Q: How to ship to us?
A: It is available by air, or by sea, or by train.
Q: How to pay the money?
A: T/T and L/C are preferred, with a different currency, including USD, EUR, RMB, etc.
Q: How can I know the product is suitable for me?
A: >1ST confirm drawing and specification >2nd test sample >3rd start mass production.
Q: Can I come to your company to visit?
A: Yes, you are welcome to visit us at any time.
Q: How shall we contact you?
A: You can send an inquiry directly, and we will respond within 24 hours.
Hot Tags: speed reducer motor, China, suppliers, manufacturers, factory, wholesale, price
Previous
Electric Motor EngineNext
Motor ReducerYou Might Also Like
Send Inquiry